Home About Us Gallery Products Contact Us
Www.LaSpeedometerGear.com www.manualtransmissionkits.com www.americanhotrodsolutions.com www.adapt-a-case.com www.superior-transmission.com www.gopnh.com www.tcsproducts.com www.raybestospowertrain.com

LOW/REV. ONE WAY CLUTCH

THIS FITS 700R4 1986-UP. THE WIDE LOW REVERSE SPRING AND ROLLER CAN BE RETRO’D BACK TO 1982 WITH THE USE OF A LATE CENTER SUPPORT

GM 700R4/4L60E Bearing Kit

  1982-Up This bearing kit includes the bearings for: stator to input drum, input drum to sun gear, rear hub to case, rear planet to support, and output shaft to case. These are Koyo bearing kits which are the highest quality bearings you can put back in your transmission.

700R4 FILTER


THIS FILTER WILL REPLACE ALL 7OOR4 FILTERS 1982-1993. THIS IS AN ALLOMATIC BRAND FILTER. NOT A CHEAP OFF BRAND FILTER. THIS IS NOT WHERE YOU WANT TO SAVE MONEY BY BUYING AN INFERIOR (CHEAP) FILTER. DON’T LET A FEW DOLLARS COST YOU A TRANSMISSION. WE ONLY SELL THE BEST FILTERS.


700-R4/200-4R Low/Reverse Boost Valve And Sleeve (Superior K020 )


Problem Solver


* Replaces smaller diameter valve applications. * This valve will help keep the transmission in manual low to a higher MPH.  * Delivers more boost pressure in manual low and manual second. * Replaces worn out O.E. valves. * Made of hardened steel to resist wear.

700-R4/200-4R TV Boost Valve And Sleeve (Superior K022 )

Problem Solver

* Replaces worn out O.E. valves. * Made of hardened steel to resist wear.  * Valve boost diameter is set at .471 for higher boost capacity.  * Proper tolerance assured at bore mating surfaces.  

4L60/4L60-E Super Servo 4th apply piston & cover (Superior K034 )

Super Servo

* 4th apply piston and cover * Better holding capacity in 4th gear * Lip seal design on piston (less leakage) * Proper 4-3 (no drag) release * Constructed of billet aluminum

700-R4/4L60-E Super Servo

(Superior K012)

T1. Voted as One of Transmission Digest's "10" Best Products for 1997. 2. Largest apply area available for 700-R4. 35 percent more apply area than the Corvette servo. 3. Super positive 1-2 shift. 4. Quicker servo release on the 4-3 downshift. 5. Positive 3-2 kick down. 6. Adjustable pin tip included to set perfect band clearance. 7. Great for heavy service, towing, racing and off-road. 8. Also can be installed on the 4L60-E. 9. Kit contains two-piece 6061-T6 billet aluminum piston set with three piece steel washerset, servo clip, servo pin extender, custom return spring and four piece Teflon sealing ring and O-ring set.

GM 700-R4 4L60 1982-On Complete Bushing Kit This bushing kit includes a, pump, case, extension housing, front stator, rear stator, both input sun gear, rear sun gear, reaction shaft front, reaction shaft rear, reverse drum front, and reverse drum rear


700R4 TRANSGO VALVE BODY SEPARATOR PLATE


These TransGo valve body separator plates feature increased hole sizes that correspond with positioned openings for first and third plates for optimum shifting performance. They also have additional openings to reroute transmission oil in the various interrelated passages in the casing in order to decrease the shift time and produce quick, reliable shifts every time. Make your transmission work more efficiently with one of these TransGo valve body separator plates.

700R4/4L60E 13 VANE ROTOR KIT

700R4 / 4L60E high performance / high volume pump rotor kits. Turn your seven or ten vane pump into a thirteen vane pump. This kit will eliminate irregular pump pressure above 5,000 RPM. Transmission must be removed to install this kit. (When using a 13 vane pump don't raise the motor speed above idle until the transmission is full of fluid, doing so may break the pump rotor.)

700R4/4L60E/2004R 4TH GEAR LOCK-UP SOLENOID

Splice in design Lock Up Solenoid.Quick connection clips make installation a breeze on this lock-up solenoid kit .This will fit all 2004R , 700R4 , & 4L60E models , and includes a basic instruction sheet . This is the standard replacement design. Great for applications when you do not need to replace the entire harness .


700R4 TOLEDO OVERHAUL KIT FITS 82-UP

TOLEDO TTK IS THE BEST QUALITY OVERHAUL KIT ON THE MARKET.THIS OVERHAUL KIT WILL CONSIST OF THESE ITEMS;ALL THE RUBBER SEALS AND O'RINGS FOR THE TRANSMISSION.ALL THE PAPER GASKETS FOR THE TRANSMISSION.HIGH QUALITY TOP OF THE LINE FIBER PAN GASKET.

NOK FRONT PUMP HARD METAL CLAD SEAL.NOK REAR TAIL HOUSING METAL CLAD SEAL.

NOK COMPLETE SEALING RING KIT.PUMP NYLON OIL FILTER SCREEN.

GOVERNOR NYLON OIL FILTER SCREEN.TCC/PRESSURE NYLON OIL FILTER SCREEN.

NEW OEM SNAP RING FOR THE FRONT PLANET TO OUTPUT SHAFT. THESE ARE THE KITS THE PROFESSIONALS USE.  DON'T SETTLE FOR LESS.

SONNAX SMART SHELL

• Heavy Duty Reaction Shell• Four-Tab Enclosed Thrust Bearing• Custom Roller Clutch Race

Stripped or cracked shells in GM 4L60, 4L60-E, 4L65-E and 4L70-E units are a common problem, but strengthening the shell alone does nothing to address the equally common problem of a failed rear planet captured bearing. The Sonnax

SmartShell 77749-02K is a heavy duty reaction shell kit designed to prevent damage to the rear planetary assembly as well as provide a reinforced shell. Protecting the Planetary BearingIn the OE sun gear shell, the thrust load

29 ELEMENT INPUT SPRAG

DOUBLE CAGE 29 ELEMENT SPRAG FITS 1987-UP 700R4 AND 4L60E  COST $43.50

REVERSE INPUT DRUM

THIS IS A BRAND NEW AFTER MARKET DRUM. THIS AFTER MARKET IS BETTER THAN O.E. THAT DOESN'T HAPPEN OFTEN. THIS DRUM IS MADE BETTER THAN O.E. SPEC. THESE DRUMS ARE OFTEN WORE OUT IN THE TRANSMISSION AND NEED REPLACEMENT JUST ABOUT EVERY TIME.

700-R4 Kit (Superior K700-R4 )

Shift Correction Package

This valve body kit deals with these problems: * Inadequate pressure rise * Burned clutches and bands * Erratic shift points * Soft or bump up shifts * Bump on coast down shifts * Raises lock up speed * 2nd and 3rd flare up * Part throttle searching between 4th and 3rd



Addresses five weak areas of the GM

4L60, 4L60-E, 4L65-E, 4L70-E input housing: (1) flexing/bowing of the 3-4 backing plate,

(2) limited 3-4 clutch torque capacity, (3) 3-4 snap-ring blow-out, (4) input housing breakage near the input shaft spline, and (5) input housing fatigue failure.

Flexing/bowing of OE and other aftermarket backing plates is eliminated with Sonnax’s heavy duty bolt-on anchoring plate. This unique design ensures even clamping of the 3-4 clutches in higher horsepower, higher pressure applications. By eliminating the 3-4 snap ring and using a thinner yet stiffer apply plate, space is made available for additional frictions and steels. This makes it possible to simultaneously increase clutch torque capacity and eliminate the possibility of retaining ring blow-out. A steel reinforcement sleeve prevents breakage in the spline area. Housing fatigue failure resistance and housing life are significantly improved with a special treatment process that greatly reduces stress crack formation.

The Sonnax Smart-Tech input housing kit

700R4 THRUST WASHER KIT


A complete thrust washer kit for the popular GM and Chevy 700R4, 4L60E overdrive automatic transmissions from 1982-up. This includes all of the washers in the transmission for 700R4, 4L60, 4L60E, 4L65E. A total of 7 thrust washers in all. If you need a complete rebuild kit, check out our COMBO KIT PAGE.


RAYBESTOS PRO SERIES WIDE 2-4 BAND

THIS IS THE BEST BAND ON THE MARKET. IT USES ALL AVAILABLE SURFACE ON THE DRUM. FOR USE WITH A NEW DRUM ONLY. THIS BAND IS A MUST ON HIGH PERFORMANCE REBUILDS.

4l80 stage 2

 700r4 CLUTCH MODULE

STAGE-1 RED 3-4 PACK

FITS 1987-UP 700R4 AND 4L60E. COMES WITH 8 3-4 FRICTIONS TO MAXIMIZE THE 3-4 CAPACITY

Raybestos Stage-1 performance frictions are an affordable solution for performance applications that may not require the capacity of the gen2™ Blue Plate Special®, but do require a friction plate that can handle the demands that a stock tan or high energy plate cannot.

Stage-1 frictions are not limited to performance, but also enhance heavy duty applications by increasing holding capacity, while being able to withstand higher temperatures associated with towing heavy load.

INCLUDES ALL STEELS NEEDED FOR REBUILD.

4L60, 4L60-E, 4L65-E, 4L70-E SONNAX

2.84 Ratio Input Carrier Kit

The steepest first gear ratio of any four-speed automatic (3.06) belongs to the GM 4L60/E family of transmissions. The shift from 3.06 ratio (first) to 1.63 ratio (second) is a dramatic ratio change, allowing engine RPM drop that results in performance engines falling out of the optimal power band. The Sonnax 2.84 input carrier kit 77284-K changes these popular units from a "wide ratio" 3.06/1.63 to a "close ratio" 2.84/1.55 configuration with more desirable RPM drop between 1-2 and 2-3 shifts. This keeps performance engines in the optimal power band while allowing a longer pull in first and second gears, improving consistency and performance.

This high-quality carrier has several advanced design features: the gears are precision-ground to OE standards, thrust washers are highly wear-resistant PTFE-coated material and the captured bearing is thicker late design. Lube channels direct oil to the pinion pins and the unit can be disassembled for inspection and service.

Six-pinion design with advanced durability features

Keeps engine in power band on 1-2 and 2-3 shifts

Allows longer pull in first and second gears

No special tools or machining required

4L60, 4L60-E

Heavy Duty Input Shaft

SONNAX

Fits 298mm units only.

Input shaft failure is a common problem in GM 4L60 and 4L60-E units as power levels are increased. The Sonnax heavy duty input shaft 77733-10S for 298mm torque converters is made of specially heat treated steel with very hard outer layers with a more ductile inner core for strength and resistance to fracture. The feed holes are chamfered to reduce stress and the shaft is further processed by shot peening and deep cryogenic treatment. This shaft is suitable for any high-horsepower street or strip application.

High strength material for high performance applications

Chamfered feed holes and shot peening reduce stress cracks and increase service life

Deep cryogenic treatment for additional toughness

THIS IS A BUILT RIGHT LEVEL 3 KIT FOR THE 700R4 TRANSMISSION

BUILT PROPERLY THIS KIT WILL HANDLE 750HP+

ALL THE GUESS WORK HAS BEEN DONE FOR YOU. COST $2050.00

SPECIFY YEAR WHEN ORDERING. FREE SHIPPING.

HAVE QUESTIONS OR NEED TECHNICAL HELP?

CALL 318.779.1006

EMAIL TECH@BRTPERFORMANCE.COM